Why is my thread bird nesting underneath the embroidery?

Why is my thread bird nesting underneath the embroidery?

how to prevent bird nesting underneath embroideryfree machine embroidery designs
.

Bird nests are cute, right ? Well – not therefore much in the world of machine embroidery. A bird nest is a pain to clean up and can drive you insane if it keeps happening again and again. So what causes bird nesting underneath the embroidery ? And what can you do to avoid it ?

What is a bird’s nest?

A bird ’ mho nest in machine embroidery is a bunch of threads that typically occurs on the wrong side of your embellishment. The embroil mess of threads resembles a very dame ’ south nest which is how it gets it ’ south mention .

thus why is a shuttlecock ’ second nest a problem if it ’ second on the wrong side of your plan ? Because these bird ’ sulfur nests can be so big that you get a hunk on the back of your stick out. In addition, when you get a bird ’ mho nest on the back of your project, you stitching on the front tends to look pretty bad .

Why there is bird nesting underneath the embroidery

There are count of different possibilities as to why you are getting bird nesting underneath the embroidery. here are some of the most common reasons.

Your machine is threaded incorrectly

A distribute of times I can solve my bird nesting problems by wholly rethreading my machine. For case, if the ribbon international relations and security network ’ deoxythymidine monophosphate securely held between the tension phonograph record, you will get disappointing results .
I know this may sound obvious, but take a look at your manual. How does the manufacturer describe the correct thread of your machine ? You may gain some insight. Some assumptions you might have made about how to thread your machine may be wrong. consequently, it ’ s a adept mind to double check .

Thread the embroidery machine with the presser foot up

now why in the heck would this topic ? Well, when the presser foot is up, it opens up quad between the tension disk to allow your ribbon to get between those plates. If the presser metrical foot is down, the ribbon will not get in between the disk .

Incorrect orientation of your bobbin

check to see if your bobbin top down ? One way to tell if your bobbin is oriented by rights within the bobbin encase is to examine the condition of the train of thought dock ; that tail should look like a “ p ” and not a “ q ” .
proper orientation of bobbin in case

Incorrect orientation of the needle

In my embellishment machine, the flat side of the needle must face the back of the machine. If you insert my phonograph needle improperly, it can lead to fuss like boo nest .

Your threading passage is dirty.

Stray threads and dust bunnies trapped in the screw thread way on the top of the machine can cause the embroidery thread to get hung up and lead to bird nest. You can sometimes remove these bits of strings and dust by “ flossing ” your embellishment machine with some unwaxed dental floss. Make certain to floss well within your tension disk .
Another option – take a attend at your embellishment machine manual. It might provide instructions for cleaning your machine. You may besides opt to take it in to your principal for a professional clean .

Dirty bobbin case

Take the face plate off the bobbin and dust it out with a makeup brush ( or the brush that came with your machine ). then remove the bobbin cage completely and brush out that area a well .
cleaning lint under plate can prevent bird nesting
cleaning bobbin case can reduce bird nesting

Thread stuck in bobbin case

Run a business circuit board under the tension spring on your bobbin. Fuzz and strings can get caught in there which can cause bird nest .
business card can be used to remove strings stuck in bobbin case

A burr or a nick on the bobbin case or plate.

Check the bobbin case and the plate for nicks or cracks. These little divots can wreck havoc on the quality of your embroidery. While they may be hard to see, you may be able to feel them. indeed, run your finger over the bobbin plate and take out the bobbin case an run your finger around the edge of that excessively. If there ’ s any bumps, gently file the edge second to smooth with a complete file. If you are unable to smooth out the defect, I would suggest ordering a replacement part for your machine .

Bent needle

If a needle runs into a hard surface, it can easily bend which then leads to problems in subsequent sewing, i.e. dame ’ mho nest city ! Embroidery machine needles are brassy. therefore, when in doubt – fair replace your acerate leaf.

Old or crappy embroidery thread

string can make a have a major impingement on the sew quality of your embellishment. Old thread that has gotten dry and brittle, or spools that are covered in lint may tend to bird nest. besides, in truth cheap ribbon can be more prone to problems as well. figure out what type of embroidery thread works well on your machine, then stick to that mark when buying screw thread in the future .

Thread stuck inside of the machine

sometimes threads can get catch inside your machine which can lead to problems while you are embroidering. To find these furtive buggers, you ’ ll have to take off the front and possibly the side breed .
expect to the right of the lease up pry. There ’ randomness a moving joint where thread can get wrapped around. then, clean that area with tweezers and a X-acto ( or craft ) knife. To the right of that joint is the tension disk. Remove any leftover threads in between the disk so that your embroidery string will go into the tension sphere by rights .

You have a tension problem

Messing with the tension should be a last ditch campaign. I ’ ve had my unmarried needle car for 15+ years and do you know how many times I ’ ve adjusted the tension ? never. If all else fails, bring your machine in for service. They can adjust the tension and discover any issues you may have been causing those little birds to make nests underneath your embellishment .
essential Supplies for Machine Embroidery

How to clean up a bird nesting underneath the embroidery?

It ’ second tempting to want to wholly cut away a bird ’ second nest. But, the way you handle it should depend on the state of matter of the project. If your plan is to tear out all of the sew and begin again, then you need to carefully cut away all the threads, free your stick out from the embroidery machine and begin again. small carapace scissors and tweezers are your best tools to remove the bird ’ sulfur nest without cutting a trap in your project .
Believe it or not, there is actually a shuttlecock ’ mho nest removal tool kit that is specifically designed to help you remove bird ’ south nest. This small bird ’ mho nest removal set comes with two instruments : a crochet to pull the threads and a tongue, a.k.a. the “ stitch releaser ” to cut the threads .
If you have finished stitching out the project, and the front looks fine but there is a dame ’ mho nest in the back, it ’ south best to leave it entirely. The reason is because cutting away the entire bird ’ s nest could cause the whole area of embellishment to fall out. But, if the boo ’ sulfur nest is truly huge and you need to cut the bulk of the thread away, be certain to use some affray check to make sure the sewing on the front side doesn ’ t come out .
If your goal is to hide the atrocious nest, you can cover the bet on of the project with some Cloud Cover, and it will be scantily noticeable .
good luck and glad sewing !
xo
Julie
Tools to Remove Embroidery

Love free machine embroidery designs and PDF patterns?

Subscribe to the Machine Embroidery Geek newsletter for access to this vault entire of goodies !

Want to remember this? Save “Why is my thread bird nesting underneath the embroidery?” on your favorite Pinterest board

how to prevent bird nesting underneath embroidery

reference : https://youkuki.com
Category : BIRDS